Discovering Essential Plumbing Skills is Vital for Bathtub Installation
Discovering Essential Plumbing Skills is Vital for Bathtub Installation
Blog Article
This great article listed below on the subject of How to Install a Bathtub Yourself is unquestionably engaging. Give it a try and draw your own findings.
Installing a tub isn't exactly brain surgery, yet it does require strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old tub with a brand-new one is also a reasonably difficult project. If the old bathtub is conveniently accessible, the project can relocate quickly; if you need to open up a wall surface to get rid of the old bathtub and position the new bath tub, the task is much harder. In either case, the job is within a home handyman's skills, although you will require an assistant to leave the old tub and also embeded in the new one. Make certain you have actually qualified on your own for the work and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is much better to think about employing one prior to you start. Chances are you may require an expert plumber to make tube links.
This short article will certainly assist you install a brand-new tub in your shower room if you have already gotten a brand-new bathtub and also do not require to transform the arrangement of your previous water system pipes.
Your tools and also product list need to consist of the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your setup, after that the first thing you ought to do is separate the water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of getting rid of the existing taps can be quite problematic as a result of the limited gain access to that is typically the situation.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the remaining water that will certainly come from the pipelines. When the supply pipes have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from turning during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before proceeding to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next off, position the faucet in the placing hole in the bath/basin making certain that the washers are in location in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer supplied backnut. As soon as the tap is safely in place, the supply pipes can be linked to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be linked to the faucet ends first, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the bathtub in the needed placement. The wooden boards are helpful in evenly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small points.
The next objective is to make sure that the bathtub is leveled all round. This can be achieved by inspecting the spirit level and also readjusting the feet on the tub until the level checks out level.
To install taps, fit the bottom of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the other faucet.
Activate the water as well as examine all joints and brand-new pipework for leakages and also tighten them if required. Fill up the bathtub and also inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub should wait until the bathtub has actually been utilized at least when as this will certainly resolve it into its last position.
Planning for the Installment
To start with, the sustaining frame supplied with the bathroom should be fitted (if called for) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is essential to see to it that if the tap features a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps unit to prevent stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you utilize every one of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be fitted in its final position.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the installation can relocate sufficient to break a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, causing issues with moisture and possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to allow for the movement experienced when the tub remains in use. The sealer can break fairly very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also easily offered on the marketplace. It is recommended to fit the tiles using water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you like more info about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Write a remark directly below. We would be pleased to see your opinions about this page. We are looking forward to see you back again later on. If you appreciated our blog entry plz make sure you remember to share it. I cherish reading our article about How to Install a Bathtub Yourself.
Address all plumbing emergencies here. Report this page